HT(1) Series Load Cell
HT(1) type load cells are low profile. Work with principle of shear beam. They are available in 350 or 700 ohm. The flexure is made of a special alloy steel and it is ideal for low and middle capacity applications. HT(1) load cells were designed for both tension and compression applications. The sensing element is covered with special materials that isolate it from industrial environments. Stainless steel and nickel-plated HT(1) load cells are highly protected from external agents such as rain, dust, water that can make troubles for a good performance. They highly withstand to overloading and to the effects of off-axis loading.
Applications
- Material testing machine
- Lifting crane applications
- Various weighing applications
Capacity
The HT(1)series load cells are produced in 1,2,5,10,20,30,50,100 ton capacities
Technical Specifications
HT(2) Series Load Cell
HT(2) type load cells are low profile. Work with principle of shear beam. They are available in 350 or 700 ohm. The flexure is made of a special alloy steel. The sensing element is covered with special materials that isolate it from industrial environments. Stainless steel and nickel-plated HT(2) load cells are highly protected from external agents such as rain, dust, water that can make troubles for a good performance.HT(2) load cells were designed for compressing, making it ideal for middle and high capacity applications. It was produced for silo-tank weighing and weighing platform. Low profile makes them ideal especially for that kind of applications in comparison with column type load cells. The HT(2) series load cells highly withstand to the effects of off-axis loading caused by wind. For tank and silo applications the mounting accessories are available. HT(2) load cells can be used in testing machine also.
Applications
- Tank and silo weighing applications
- Middle and high weighing platfroms
- Material testing machine
Capacity
The HT(2)series load cells are produced in 1,2,5,10,20,30,50,100 ton capacities
Technical Specifications
About Weighing System
Weighing system is the key conception in physics. It had its analogues in remote past and is intended for weighing of loads mass. Physically it sounds as weight W is the product of the mass m of the object and the magnitude of the local gravitational acceleration g; thus: W = mg, where W is equal to gravity force of a mass in ground-vertical axis.
There are several methods to use the weighing system which consists of set of measuring instruments. However today is offered more comfortable and accurate the way of weighing. That is load cell. Load cell is the best transducer to display the weight on the screen. Its principle of work bases on strain gage. Strain gage is electronic structure in various sizes and forms for analyzing static and / or dynamic resistance of a system or detached structure.
Load cell works on just a single axis, since it is applied in weighing.
Load Cell
Pancake Load Cells
HT(1) Series Load Cell is ideal for low and middle capacity applications. Low profiled and designed for both tension and compression applications. Highly withstands to overloading and to the effects of off-axis loading.
HT(2) Series Load Cell is ideal for middle and high capacity applications. Low profiled and designed for compression applications. Highly withstands to the effects of off-axis loading.
‘S’ Type Load Cells
ST Series Load Cell is suitable for low and middle capacity applications or for force meters. It is designed for tension or compression or both for tension and compression applications. Has ex-proof version.
ST-2W C Series Load Cell is ideal for middle and high capacity applications or for force meters. Has electrostatically charged paint cover and designed for compression applications.10 Tons capacity for tension applications is available.
ST-2W TC Series Load Cell is ideal for middle and high capacity applications or for force meters. Has electrostatically charged paint cover and designed for compression applications.10 Tons capacity for tension applications is available.
STA Aluminium Series Load Cell is ideal for low capacity applications or for force meters. Designed for tension or compression or for both tension and compression applications.
Shear Beam Load Cells
LT-5C Series Load Cell is single ended with IP68 nipple cable. Designed for compression applications. Has ex-proof version.
LTE Series Load Cell is single ended with IP68 nipple cable. Designed for compression applications.
Bending Beam Load Cells
BT Series Load Cell developed for low or middle capacity applications. Its cable is sealed to metal nipple. Protection level is IP68.
RT Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 60 cm x 60 cm.
PL Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 40 cm x 40 cm.
PS Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 30 cm x 30 cm.
PD Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 20 cm x 20 cm.
MT Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 15 cm x 15 cm.
Column Type Load Cells
CT Series Load Cell designed for truck scales and silo weighing applications. The body is completely closed with welding and is in IP68 class.
Web Tension Control Type Load Cells
RS Series Load Cell developed to control reel tension in winding / unwinding system. It shows the force applied to reel while load cell is in use.
Special Load Cells
Load Pin used at cranes for measurement of force on working platforms. It shows the force applied to reel by load by sending the electrical signal to display.
Weighing Indicator
HGX-1000 Weighing Indicator
HGX-1000 Weighing Indicator includes 3 digital inputs / 2 relay outputs feature and is able to communicate with PC and PLC systems.
FSM-2 Weighing Indicator
FSM-2 Weighing Indicator used in various weighing applications such as bench scales, silo and tank weighing platforms. Has an aluminium frame.
FSM-2 Ex-proof Weighing Indicator
FSM-2 Ex-proof Weighing Indicator is ideal for use in chemical and petroleum industries, encompassing explosion risk.
FSM-2 S Weighing Indicator
FSM-2 S Weighing Indicator has stainless steel box that protects from dust and water. Used in various weighing appliances such as platform scales, silo and tank weighing etc.
PA-10 Load Cell Transmitter
PA-10 Load Cell Transmitter is the signal amplifier to transmit the load cell signals to further distances or to make the load cell signal compatible with process control system. Signal output is 0-10V
PD-20 Load Cell Transmitter
PD-20 Load Cell Transmitter designed to combine reliable weight information from process vessels with extremely easy operation and setup. Output is provided in 4-20 mA signal format.
Weighing Systems
Phantom Crane Scale
Phantom Crane Scale is used for material weighing when it is loaded or unloaded. It may reset, lead to deadweight and sum. Has 20 mm 7 segments bright display. Produced in 2, 5, 7 ton capacities.
Check – Weigher
Check – Weigher is the weight control of packaged products carried on the conveyor belts. Over or lack of weight products are removed from the belt by means of air.
HT(1) type load cells are low profile. Work with principle of shear beam. They are available in 350 or 700 ohm. The flexure is made of a special alloy steel and it is ideal for low and middle capacity applications. HT(1) load cells were designed for both tension and compression applications. The sensing element is covered with special materials that isolate it from industrial environments. Stainless steel and nickel-plated HT(1) load cells are highly protected from external agents such as rain, dust, water that can make troubles for a good performance. They highly withstand to overloading and to the effects of off-axis loading.
Applications
- Material testing machine
- Lifting crane applications
- Various weighing applications
Capacity
The HT(1)series load cells are produced in 1,2,5,10,20,30,50,100 ton capacities
Technical Specifications
| Type | HT(1) | |||
| Accuracy class | C1 1000d | |||
| Capacity (Emax) | 1-2-5-10-20-30-50-100 T | |||
| Minimum dead load | 0% R.O | |||
| Rated output R.O | 2,0 mV/V | |||
| Maximum number of load cell interval Nmax | 1000 | |||
| Vmin | Emax/4000 | |||
| Emax / Vmin | 4000 | |||
| Minimum dead load output return (MDLOR) | <0,0500 %R.O | |||
| Zero balance | 1 %R.O | |||
| Temperature effect on zero | << 0,0070 %R.O/5°C | |||
| Temperature effect on output | < 0,0055 %R.O/5°C | |||
| Compensated temperature range | -10 /+40 °C | |||
| Temperature range safe | -30 /+70 °C | |||
| Maximum safe central overload | 150 %R.O | |||
| Ultimate central overload | 300 %R.O | |||
| Excitation | 5 V | |||
| Input impedance | 760±60 ? | |||
| Output impedance | 700±6 ? | |||
| Insulation resistance | >1000 M? | |||
| Construction | Nickel plated alloy steel | |||
| Environmental protection | IP67 | |||
| Cable type | 2x2x0,22 mm | |||
| Cable length | 1-2-5T 3m | |||
| 10-20-30-50-100T 5m | ||||
| Weight | 1-2-5T 10-20T 30-50T 100T | ? kg | ||
HT(2) Series Load Cell
HT(2) type load cells are low profile. Work with principle of shear beam. They are available in 350 or 700 ohm. The flexure is made of a special alloy steel. The sensing element is covered with special materials that isolate it from industrial environments. Stainless steel and nickel-plated HT(2) load cells are highly protected from external agents such as rain, dust, water that can make troubles for a good performance.HT(2) load cells were designed for compressing, making it ideal for middle and high capacity applications. It was produced for silo-tank weighing and weighing platform. Low profile makes them ideal especially for that kind of applications in comparison with column type load cells. The HT(2) series load cells highly withstand to the effects of off-axis loading caused by wind. For tank and silo applications the mounting accessories are available. HT(2) load cells can be used in testing machine also.
Applications
- Tank and silo weighing applications
- Middle and high weighing platfroms
- Material testing machine
Capacity
The HT(2)series load cells are produced in 1,2,5,10,20,30,50,100 ton capacities
Technical Specifications
| Type | HT(2) | ||
| Accuracy class | C1 | ||
| Capacity (Emax) | 1-2-5-10-20-30-50 T | ||
| Minimum dead load | 0% R.O | ||
| Rated output R.O | 2,0 mV/V | ||
| Maximum number of load cell interval Nmax | 1000 | ||
| Vmin | Emax/4000 | ||
| Emax / Vmin | 4000 | ||
| Minimum dead load output return (MDLOR) | <0,0500 %R.O | ||
| Zero balance | 1 %R.O | ||
| Temperature effect on zero | << 0,0070 %R.O/5°C | ||
| Temperature effect on output | < 0,0055 %R.O/5°C | ||
| Compensated temperature range | -10 /+40 °C | ||
| Temperature range safe | -30 /+70 °C | ||
| Maximum safe central overload | 150 %R.O | ||
| Ultimate central overload | 300 %R.O | ||
| Excitation | 5 V | ||
| Input impedance | 380±20 760±40 Ω | ||
| Output impedance | 350±3 700±6 Ω | ||
| Insulation resistance | >1000 MΩ | ||
| Construction | Nickel plated alloy steel | ||
| Environmental protection | IP67 | ||
| Cable type | 2x2x0,22 mm | ||
| Cable length | 1-2-5T 3m | ||
| 10-20-30-50-100T 15m | |||
| Weight | 10-20T : 3,5 kg |
About Weighing System
Weighing system is the key conception in physics. It had its analogues in remote past and is intended for weighing of loads mass. Physically it sounds as weight W is the product of the mass m of the object and the magnitude of the local gravitational acceleration g; thus: W = mg, where W is equal to gravity force of a mass in ground-vertical axis.
There are several methods to use the weighing system which consists of set of measuring instruments. However today is offered more comfortable and accurate the way of weighing. That is load cell. Load cell is the best transducer to display the weight on the screen. Its principle of work bases on strain gage. Strain gage is electronic structure in various sizes and forms for analyzing static and / or dynamic resistance of a system or detached structure.
Load cell works on just a single axis, since it is applied in weighing.
Load Cell
Pancake Load Cells
HT(1) Series Load Cell is ideal for low and middle capacity applications. Low profiled and designed for both tension and compression applications. Highly withstands to overloading and to the effects of off-axis loading.
HT(2) Series Load Cell is ideal for middle and high capacity applications. Low profiled and designed for compression applications. Highly withstands to the effects of off-axis loading.
‘S’ Type Load Cells
ST Series Load Cell is suitable for low and middle capacity applications or for force meters. It is designed for tension or compression or both for tension and compression applications. Has ex-proof version.
ST-2W C Series Load Cell is ideal for middle and high capacity applications or for force meters. Has electrostatically charged paint cover and designed for compression applications.10 Tons capacity for tension applications is available.
ST-2W TC Series Load Cell is ideal for middle and high capacity applications or for force meters. Has electrostatically charged paint cover and designed for compression applications.10 Tons capacity for tension applications is available.
STA Aluminium Series Load Cell is ideal for low capacity applications or for force meters. Designed for tension or compression or for both tension and compression applications.
Shear Beam Load Cells
LT-5C Series Load Cell is single ended with IP68 nipple cable. Designed for compression applications. Has ex-proof version.
LTE Series Load Cell is single ended with IP68 nipple cable. Designed for compression applications.
Bending Beam Load Cells
BT Series Load Cell developed for low or middle capacity applications. Its cable is sealed to metal nipple. Protection level is IP68.
RT Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 60 cm x 60 cm.
PL Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 40 cm x 40 cm.
PS Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 30 cm x 30 cm.
PD Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 20 cm x 20 cm.
MT Series Load Cell designed for tension or compression or for both tension and compression applications. It is highly resistant to eccentric loading. Platform sizes are 15 cm x 15 cm.
Column Type Load Cells
CT Series Load Cell designed for truck scales and silo weighing applications. The body is completely closed with welding and is in IP68 class.
Web Tension Control Type Load Cells
RS Series Load Cell developed to control reel tension in winding / unwinding system. It shows the force applied to reel while load cell is in use.
Special Load Cells
Load Pin used at cranes for measurement of force on working platforms. It shows the force applied to reel by load by sending the electrical signal to display.
Weighing Indicator
HGX-1000 Weighing Indicator
HGX-1000 Weighing Indicator includes 3 digital inputs / 2 relay outputs feature and is able to communicate with PC and PLC systems.
FSM-2 Weighing Indicator
FSM-2 Weighing Indicator used in various weighing applications such as bench scales, silo and tank weighing platforms. Has an aluminium frame.
FSM-2 Ex-proof Weighing Indicator
FSM-2 Ex-proof Weighing Indicator is ideal for use in chemical and petroleum industries, encompassing explosion risk.
FSM-2 S Weighing Indicator
FSM-2 S Weighing Indicator has stainless steel box that protects from dust and water. Used in various weighing appliances such as platform scales, silo and tank weighing etc.
PA-10 Load Cell Transmitter
PA-10 Load Cell Transmitter is the signal amplifier to transmit the load cell signals to further distances or to make the load cell signal compatible with process control system. Signal output is 0-10V
PD-20 Load Cell Transmitter
PD-20 Load Cell Transmitter designed to combine reliable weight information from process vessels with extremely easy operation and setup. Output is provided in 4-20 mA signal format.
Weighing Systems
Phantom Crane Scale
Phantom Crane Scale is used for material weighing when it is loaded or unloaded. It may reset, lead to deadweight and sum. Has 20 mm 7 segments bright display. Produced in 2, 5, 7 ton capacities.
Check – Weigher
Check – Weigher is the weight control of packaged products carried on the conveyor belts. Over or lack of weight products are removed from the belt by means of air.
